Search Results

Search found 13033 results on 522 pages for '12 04 1'.

Page 375/522 | < Previous Page | 371 372 373 374 375 376 377 378 379 380 381 382  | Next Page >

  • Wireless connection by using command screen

    - by Amadeus
    I installed Ubuntu 12.04 armhf to my beagleboard-xm and now trying to connect to a wireless network. First, I checked if I can search for available networks: ubuntu@arm:~$ iwlist scan lo Interface doesn't support scanning. usb0 Interface doesn't support scanning. wlan0 Scan completed : Cell 01 - Address: EA:7D:EF:60:C9:0B Channel:1 Frequency:2.412 GHz (Channel 1) Quality=70/70 Signal level=-23 dBm Encryption key:on ESSID:"ghostrider" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Ad-Hoc Extra:tsf=000000005a1ab50e Extra: Last beacon: 6242ms ago IE: Unknown: 000A67686F73747269646572 IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 06020000 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: Unknown: 32040C121860 IE: Unknown: 2D1A2C181BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D16010800000000FF000000000000000000000000000000 IE: Unknown: DD09001018020000000000 Then I edited /etc/network/interfaces file to the following: root@arm:/etc/wpa_supplicant# cat /etc/network/interfaces auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # Example to keep MAC address between reboots #hwaddress ether DE:AD:BE:EF:CA:FE # WiFi Example auto wlan0 iface wlan0 inet dhcp wpa-ssid "ghostrider" wpa-psk "b34d373eb2fb836a43b0afffe783c7d0af694724506c9e77b06d1021302905bf" But I cannot still connect to the wireless network: root@arm:/etc/wpa_supplicant# iwconfig lo no wireless extensions. usb0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Asociated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on eth0 no wireless extensions. root@arm:/etc/network# ifup wlan0 Failed to bring up wlan0. What is wrong? Should I change any other files also? But I think it was enough. By the way if you are curious about where that wpa-psk came from: zero@ghostrider:~$ wpa_passphrase ghostrider 34bddf67c2 network={ ssid="ghostrider" #psk="34bddf67c2" psk=b34d373eb2fb836a43b0afffe783c7d0af694724506c9e77b06d1021302905bf } I will appreciate any effort to help. Regards, Amadeus ps: Also I tried to connect manually: root@arm:/etc/network# iwconfig wlan0 essid ghostrider key s:34bddf67c2 But this did not solve my problem also.

    Read the article

  • What actions does Ubuntu trigger when battery is low?

    - by blueyed
    When the battery is low, the screen gets dimmed after a few seconds already. This appears to be some special power-saving mode, and might be related to the time in org.gnome.settings-daemon.plugins.power.time-low (1200 seconds (20 minutes) the default). While this seems to get triggered by gnome-settings-daemon, I wonder what else Ubuntu does when this happens (e.g. via DBus listeners), or other event listeners that look for a "low battery" state. It seems like something in this regard causes Ubuntu / X / the system to behave more sluggish afterwards (when the laptop is on AC again), and I would like to look into what might be causing this. I could not find anything related via dconf-editor, e.g. in org.gnome.settings-daemon.plugins.power. It appears to get setup via idle_configure in plugins/power/gsd-power-manager.c, but it's probably something more related to something that listens on the DBus interface, which gets notified via e.g.: if (!g_dbus_connection_emit_signal (manager->priv->connection, NULL, GSD_POWER_DBUS_PATH, "org.freedesktop.DBus.Properties", "PropertiesChanged", props_changed, &error)) I could imagine that some "power saving" property gets set, but not unset when AC is available anymore and/or the battery is not low anymore. I have looked at the CPU governor setting (/sys/devices/system/cpu/cpu*/cpufreq/scaling_governor), but it was ondemand. I am using gnome-settings-daemon with awesomeWM on Ubuntu 14.04. gnome-settings-daemon=3.8.6.1-0ubuntu11.1 I've also compared gsd's plugins/power/gsd-power-manager.c with the one from Debian's gnome-settings-daemon-3.12.1, but could not find anything obvious that might have been fixed/changed in this regard. I have managed to trigger the gnome-power-manager's gnome-settings plugin (which dims the screen etc), by patching upower and use it after killing the system's upower daemon. (note that it's probably only energy that is being used by gpm to calculate it by itself). It does not make the system become sluggish.. OTOH I have not heard the speaker's beeping, which might come from the BIOS, which might be involved here, too - or other programs using the kernel's interface on /sys/class/power_supply/BAT0/. --- src/linux/up-device-supply.c.orig 2014-06-07 16:48:32.735920661 +0200 +++ src/linux/up-device-supply.c 2014-06-07 16:48:39.391920525 +0200 @@ -821,6 +821,9 @@ supply->priv->energy_old_first = 0; } + percentage = 3.1f; + time_to_empty = 3*60; + energy = 5; g_object_set (device, "energy", energy, "energy-full", energy_full,

    Read the article

  • EBusiness Maintenace Wizard

    - by cwarticki
    Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Seriously folks, you'd be amazed by the power and functionality of this tool.  If you're an EBus customer, you must use the Maintenance Wizard.  I know customers that have logged 2000+ SRs doing EBus upgrades the hard way and others that have use the Maintenance Wizard and have performed production upgrades on 7 global instances with only a handful of SRs.  You decide which is better. Oh, btw......it's part of your Premier Support investment. No additional cost necessary. -Chris Warticki The Maintenance Wizard is an E-Business Suite upgrade tool that can guide you through the code line upgrade process from 11.5.10.2 to 12.1.3 with an 11gR2 database. Additionally, it includes maintenance features for most releases of E-Business Suite applications. The Tool: * Presents step-by-step upgrade and maintenance processes * Enables validation of each step, tracks the completion of the steps, and maintains a log and status * Is a multi-user tool that enables the System Administrator to give different users assignments based on any combination of category, product family or task * Automatically installs many required patches * Provides project management utilities to record the time taken for each task, completion status and project reporting For More Information: * Review Note 215527.1 for additional information on the Maintenance Wizard * See Note 430732.1 to download the new Patch Sincerely, Oracle Proactive Support Center

    Read the article

  • Bukkit saving inventory

    - by HcgRandon
    Alright i will make this quick... I am working on a command in my plugin to allow you to transfer worlds and i am trying to save inventory but i am getting a problem here is the code: public void savePlayerInv(Player p, World w){ File playerInvConfigFile = new File(plugin.getDataFolder() + File.separator + "players" + File.separator + p.getName(), "inventory.yml"); FileConfiguration pInv = YamlConfiguration.loadConfiguration(playerInvConfigFile); PlayerInventory inv = p.getInventory(); int i = 0; for (ItemStack stack : inv.getContents()) { //increment integer i++; String startInventory = w.getName() + ".inv." + Integer.toString(i); //save inv pInv.set(startInventory + ".amount", stack.getAmount()); pInv.set(startInventory + ".durability", Short.toString(stack.getDurability())); pInv.set(startInventory + ".type", stack.getTypeId()); //pInv.set(startInventory + ".enchantment", stack.getEnchantments()); //TODO add enchant saveing } i = 0; for (ItemStack armor : inv.getArmorContents()){ i++; String startArmor = w.getName() + ".armor." + Integer.toString(i); //save armor pInv.set(startArmor + ".amount", armor.getAmount()); pInv.set(startArmor + ".durability", armor.getDurability()); pInv.set(startArmor + ".type", armor.getTypeId()); //pInv.set(startArmor + ".enchantment", armor.getEnchantments()); } //save exp if (p.getExp() != 0) { pInv.set(w.getName() + ".exp", p.getExp()); } } Now here is the stack trace i recive it is commplaing about line 130 which is this line pInv.set(startInventory + ".amount", stack.getAmount()); okay now trace 2012-03-21 13:23:25 [SEVERE] null org.bukkit.command.CommandException: Unhandled exception executing command 'wtp' in plugin Needs v1.0 at org.bukkit.command.PluginCommand.execute(PluginCommand.java:42) at org.bukkit.command.SimpleCommandMap.dispatch(SimpleCommandMap.java:166) at org.bukkit.craftbukkit.CraftServer.dispatchCommand(CraftServer.java:461) at net.minecraft.server.NetServerHandler.handleCommand(NetServerHandler.java:818) at net.minecraft.server.NetServerHandler.chat(NetServerHandler.java:778) at net.minecraft.server.NetServerHandler.a(NetServerHandler.java:761) at net.minecraft.server.Packet3Chat.handle(Packet3Chat.java:33) at net.minecraft.server.NetworkManager.b(NetworkManager.java:229) at net.minecraft.server.NetServerHandler.a(NetServerHandler.java:112) at net.minecraft.server.NetworkListenThread.a(NetworkListenThread.java:78) at net.minecraft.server.MinecraftServer.w(MinecraftServer.java:554) at net.minecraft.server.MinecraftServer.run(MinecraftServer.java:452) at net.minecraft.server.ThreadServerApplication.run(SourceFile:490) Caused by: java.lang.NullPointerException at com.devoverflow.improved.needs.commands.CommandWorldtp.savePlayerInv(CommandWorldtp.java:130) at com.devoverflow.improved.needs.commands.CommandWorldtp.onCommand(CommandWorldtp.java:60) at org.bukkit.command.PluginCommand.execute(PluginCommand.java:40) ... 12 more

    Read the article

  • 13.10 upgrade dropping wifi [on hold]

    - by Daryl
    Almost a complete newb here. After my last upgrade from 12.04 to 13.10 my wifi now randomly drops. The only way I can get a signal back is a shutdown and restart otherwise it shows no network is even available to connect to. Had no problems until the upgrade. Any help would be appreciated. H/W path Device Class Description ==================================================== system h8-1534 (H2N64AA#ABA) /0 bus 2AC8 /0/0 memory 64KiB BIOS /0/4 processor AMD FX(tm)-6200 Six-Core Processor /0/4/5 memory 288KiB L1 cache /0/4/6 memory 6MiB L2 cache /0/4/7 memory 8MiB L3 cache /0/d memory 10GiB System Memory /0/d/0 memory DIMM Synchronous [empty] /0/d/1 memory 4GiB DIMM DDR3 Synchronous 1600 MHz (0.6 ns) /0/d/2 memory 2GiB DIMM DDR3 Synchronous 1600 MHz (0.6 ns) /0/d/3 memory 4GiB DIMM DDR3 Synchronous 1600 MHz (0.6 ns) /0/100 bridge RD890 PCI to PCI bridge (external gfx0 port B) /0/100/0.2 generic RD990 I/O Memory Management Unit (IOMMU) /0/100/2 bridge RD890 PCI to PCI bridge (PCI express gpp port B) /0/100/2/0 display Turks PRO [Radeon HD 7570] /0/100/2/0.1 multimedia Turks/Whistler HDMI Audio [Radeon HD 6000 Series] /0/100/5 bridge RD890 PCI to PCI bridge (PCI express gpp port E) /0/100/5/0 bus TUSB73x0 SuperSpeed USB 3.0 xHCI Host Controller /0/100/11 storage SB7x0/SB8x0/SB9x0 SATA Controller [RAID5 mode] /0/100/12 bus SB7x0/SB8x0/SB9x0 USB OHCI0 Controller /0/100/12.2 bus SB7x0/SB8x0/SB9x0 USB EHCI Controller /0/100/13 bus SB7x0/SB8x0/SB9x0 USB OHCI0 Controller /0/100/13.2 bus SB7x0/SB8x0/SB9x0 USB EHCI Controller /0/100/14 bus SBx00 SMBus Controller /0/100/14.2 multimedia SBx00 Azalia (Intel HDA) /0/100/14.3 bridge SB7x0/SB8x0/SB9x0 LPC host controller /0/100/14.4 bridge SBx00 PCI to PCI Bridge /0/100/14.5 bus SB7x0/SB8x0/SB9x0 USB OHCI2 Controller /0/100/15 bridge SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0) /0/100/15.1 bridge SB700/SB800/SB900 PCI to PCI bridge (PCIE port 1) /0/100/15.2 bridge SB900 PCI to PCI bridge (PCIE port 2) /0/100/15.2/0 wlan0 network RT3290 Wireless 802.11n 1T/1R PCIe /0/100/15.2/0.1 generic RT3290 Bluetooth /0/100/15.3 bridge SB900 PCI to PCI bridge (PCIE port 3) /0/100/15.3/0 eth0 network RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller /0/100/16 bus SB7x0/SB8x0/SB9x0 USB OHCI0 Controller /0/100/16.2 bus SB7x0/SB8x0/SB9x0 USB EHCI Controller /0/101 bridge Family 15h Processor Function 0 /0/102 bridge Family 15h Processor Function 1 /0/103 bridge Family 15h Processor Function 2 /0/104 bridge Family 15h Processor Function 3 /0/105 bridge Family 15h Processor Function 4 /0/106 bridge Family 15h Processor Function 5 /0/1 scsi0 storage /0/1/0.0.0 /dev/sda disk 1TB WDC WD1002FAEX-0 /0/1/0.0.0/1 volume 189MiB Windows FAT volume /0/1/0.0.0/2 /dev/sda2 volume 244MiB data partition /0/1/0.0.0/3 /dev/sda3 volume 931GiB LVM Physical Volume /0/2 scsi2 storage /0/2/0.0.0 /dev/cdrom disk DVD A DH16ACSHR /0/3 scsi6 storage /0/3/0.0.0 /dev/sdb disk SCSI Disk /0/3/0.0.1 /dev/sdc disk SCSI Disk /0/3/0.0.2 /dev/sdd disk SCSI Disk /0/3/0.0.3 /dev/sde disk MS/MS-Pro /0/3/0.0.3/0 /dev/sde disk /1 power Standard Efficiency I apologize for my newbness. I hope this is enough info for the hardware. Thanks Bruno for pointing out I needed to add more info. If I am lacking anything else please let me know and I'll post it.

    Read the article

  • Legal concerns with orchestrating a music submission contest

    - by Amplify91
    My team and I are getting pretty far along in the development of our latest game and have been thinking about audio. We decided to host an audio submission contest where we will offer a little cash and some equity stake in the game as prizes. We are also giving away copies of the game to participants. We hope not only to find audio for our game, but to meet some cool sound artists and promote the game a bit through the process. First of all, is this even a good idea? What are some potential dangers in doing this? Will it even be well received among artists? Secondly, I wrote up some Terms and Conditions in my best legal-speak to try to protect us and clarify how the contest will be run. Are these sufficient to make sure everyone involved is treated fairly and is legally protected? They are as follows: All submissions (The Submission) must be licensed under a Creative Commons Attribution 3.0 Unported License (CC-BY-3.0) By applying a CC-BY-3.0 license, you (The Submitter) expressly give Detour Games (and all members wherein) permission to copy, distribute, transmit, modify, adapt, and make commercial use of The Submission. The Submitter must own all rights to The Submission and be within their rights to license it as specified and submit it. The Submitter claims responsibility for the legality of The Submission. If The Submission is found to infringe on the rights of a person or entity other than those of The Submitter, Detour Games will not be held liable as all responsibility and liability for the legality of The Submission is that of The Submitter's. No more than two free copies of The Game per submitter. All flat cash prizes will only be disbursed pending the success of our first $5,000 Kickstarter campaign. These prizes will be disbursed 30 days after Detour Games receives the Kickstarter funds. All equity prizes (percentage of profits) are defined as the given percent of total profits after costs for a period of one year (12 months) after the release of RAW. These prizes will be disbursed semi-annually. All prize money will be disbursed through either an electronic fund transfer through a service such as PayPal or by a mailed money order. It is The Submitter's responsibility to cooperate with Detour Games in the disbursement of the funds. Detour Games reserves the right to change these Terms and Conditions at any time without notice. By participating in the contest, The Submitter agrees to and accepts all terms and conditions listed. What else could I do (legally) to protect everyone involved?

    Read the article

  • Creating a Yes/No MessageBox in a NuGet install/uninstall script

    - by ParadigmShift
    Sometimes getting a little feedback during the install/uninstall process of a NuGet package could be really useful. Instead of accounting for all possible ways to install your NuGet package for every user, you can simplify the installation by clarifying with the user what they want. This example shows how to generate a windows yes/no message box to get input from the user in the PowerShell install or uninstall script. We’ll use the prompt on the uninstall to confirm if the user wants to delete a custom setting that the initial install placed in their configuration.  Obviously you could use the prompt in any way you want. The objects of the message box are generated similar to the controls in the code behind of a WinForm. At the beginning of your script enter this: param($installPath, $toolsPath, $package, $project)   # Set up path variables $solutionDir = Get-SolutionDir $projectName = (Get-Project).ProjectName $projectPath = Join-Path $solutionDir $projectName   ################################################################################################ # WinForm generation for prompt ################################################################################################ function Ask-Delete-Custom-Settings { [void][reflection.assembly]::loadwithpartialname("System.Windows.Forms") [Void][reflection.assembly]::loadwithpartialname("System.Drawing")   $title = "Package Uninstall" $message = "Delete the customized settings?" #Create form and controls $form1 = New-Object System.Windows.Forms.Form $label1 = New-Object System.Windows.Forms.Label $btnYes = New-Object System.Windows.Forms.Button $btnNo = New-Object System.Windows.Forms.Button   #Set properties of controls and form ############ # label1 # ############ $label1.Location = New-Object System.Drawing.Point(12,9) $label1.Name = "label1" $label1.Size = New-Object System.Drawing.Size(254,17) $label1.TabIndex = 0 $label1.Text = $message   ############# # btnYes # ############# $btnYes.Location = New-Object System.Drawing.Point(156,45) $btnYes.Name = "btnYes" $btnYes.Size = New-Object System.Drawing.Size(48,25) $btnYes.TabIndex = 1 $btnYes.Text = "Yes"   ########### # btnNo # ########### $btnNo.Location = New-Object System.Drawing.Point(210,45) $btnNo.Name = "btnNo" $btnNo.Size = New-Object System.Drawing.Size(48,25) $btnNo.TabIndex = 2 $btnNo.Text = "No"   ########### # form1 # ########### $form1.ClientSize = New-Object System.Drawing.Size(281,86) $form1.Controls.Add($label1) $form1.Controls.Add($btnYes) $form1.Controls.Add($btnNo) $form1.Name = "Form1" $form1.Text = $title #Event Handler $btnYes.add_Click({btnYes_Click}) $btnNo.add_Click({btnNo_Click}) return $form1.ShowDialog() } function btnYes_Click { #6 = Yes $form1.DialogResult = 6 } function btnNo_Click { #7 = No $form1.DialogResult = 7 } ################################################################################################ This has also wired up the click events to the form.  This is all it takes to create the message box. Now we have to actually use the message box and get the user’s response or this is all pointless.  We’ll then delete the section of the application/web configuration called <Custom.Settings> [xml] $configXmlContent = Get-Content $configFile   Write-Host "Please respond to the question in the Dialog Box." $dialogResult = Ask-Delete-Custom-Settings #6 = Yes #7 = No Write-Host "dialogResult = $dialogResult" if ($dialogResult.ToString() -eq "Yes") { Write-Host "Deleting customized settings" $customSettingsNode = $configXmlContent.configuration.Item("Custom.Settings") $configXmlContent.configuration.RemoveChild($customSettingsNode) $configXmlContent.Save($configFile) } if ($dialogResult.ToString() -eq "No") { Write-Host "Do not delete customized settings" } The part where I check if ($dialog.Result.ToString() –eq “Yes”) could just as easily check the value for either 6 or 7 (Yes or No).  I just personally decided I liked this way better.   Shahzad Qureshi is a Software Engineer and Consultant in Salt Lake City, Utah, USA His certifications include: Microsoft Certified System Engineer 3CX Certified Partner Global Information Assurance Certification – Secure Software Programmer – .NET He is the owner of Utah VoIP Store at http://www.utahvoipstore.com/ and SWS Development at http://www.swsdev.com/ and publishes windows apps under the name Blue Voice.

    Read the article

  • SharePoint Search Problem: The crawler could not communicate with the server.

    - by Clara Oscura
    This one was not easy to solve ... Error: The crawler could not communicate with the server. Check that the server is available and that the firewall access is configured. Context: Some pages were not crawled (giving the above error) and, what is worse, all the sub content of that site was not crawled either! (the pages were the homepages of the site) Solution:The pages that could not be crawled due to this error contained a custom web part. This web part used default credentials for a given action. During crawling, the SP_Search account tried to perform this action but did not have the appropriate rights. This gave an error that stopped the crawling for the whole site. This blog helped me: http://patricklamber.blogspot.com/2010/04/why-might-moss-crawler-not-working.html

    Read the article

  • Silverlight and WCF caching

    - by subodhnpushpak
    There are scenarios where Silverlight client calls WCF (or REST) service for data. Now, if the data is cached on the WCF layer, the calls can take considerable resources at the server if NOT cached. Keeping that in mind along with the fact that cache is an cross-cutting aspect, and therefore it should be as easy as possible to put Cache wherever required. The good thing about the solution is that it caches based on the inputs. The input can be basic type of any complex type. If input changes the data is fetched and then cached for further used. If same input is provided again, data id fetched from the cache. The cache logic itself is implemented as PostSharp aspect, and it is as easy as putting an attribute over service call to switch on cache. Notice how clean the code is:        [OperationContract]       [CacheOnArgs(typeof(int))] // based on actual value of cache        public string DoWork(int value)        {            return string.Format("You entered: {0} @ cached time {1}", value, System.DateTime.Now);        } The cache is implemented as POST Sharp as below 1: public override void OnInvocation(MethodInvocationEventArgs eventArgs) 2: { 3: try 4: { 5: object value = new object(); 6: object[] args = eventArgs.GetArgumentArray(); 7: if (args != null || args.Count() > 0) 8: { 9:   10: string key = string.Format("{0}_{1}", eventArgs.Method.Name, XMLUtility<object>.GetDataContractXml(args[0], null));// Compute the cache key (details omitted). 11:   12: 13: value = GetFromCache(key); 14: if (value == null) 15: { 16: eventArgs.Proceed(); 17: value = XMLUtility<object>.GetDataContractXml(eventArgs.ReturnValue, null); 18: value = eventArgs.ReturnValue; 19: AddToCache(key, value); 20: return; 21: } 22:   23:   24: Log(string.Format("Data returned from Cache {0}",value)); 25: eventArgs.ReturnValue = value; 26: } 27: } 28: catch (Exception ex) 29: { 30: //ApplicationLogger.LogException(ex.Message, Source.UtilityService); 31: } 32: } 33:   34: private object GetFromCache(string inputKey) { if (ServerConfig.CachingEnabled) { return WCFCache.Current[inputKey]; } return null; }private void AddToCache(string inputKey,object outputValue) 35: { 36: if (ServerConfig.CachingEnabled) 37: { 38: if (WCFCache.Current.CachedItemsNumber < ServerConfig.NumberOfCachedItems) 39: { 40: if (ServerConfig.SlidingExpirationTime <= 0 || ServerConfig.SlidingExpirationTime == int.MaxValue) 41: { 42: WCFCache.Current[inputKey] = outputValue; 43: } 44: else 45: { 46: WCFCache.Current.Insert(inputKey, outputValue, new TimeSpan(0, 0, ServerConfig.SlidingExpirationTime), true); 47:   48: // _bw.DoWork += bw_DoWork; 49: //string arg = string.Format("{0}|{1}", inputKey,outputValue); 50: //_bw.RunWorkerAsync(inputKey ); 51: } 52: } 53: } 54: }     The cache class can be extended to support Velocity / memcahe / Nache. the attribute can be used over REST services as well. Hope the above helps. Here is the code base for the same.   Please do provide your inputs / comments.

    Read the article

  • "You are missing the following 32-bit libraries, and Steam may not run: libc.so.6" The common fixes don't work,

    - by M_Steam_User
    So I know this is a problem that has been asked around a lot, but I've tried a bunch of solutions with no success. I'm running Ubuntu 12.04 (64 bit), and I just installed it yesterday. This is my first time working with linux. The error is: You are missing the following 32-bit libraries, and Steam may not run: libc.so.6 Things I've tried. First, I had downloaded from the steam website. I uninstalled it, and tried again from the ubuntu software centre. sudo apt-get update sudo apt-get install ia32-libs sudo apt-get upgrade This installed a bunch of the 32 bit libraries, but did not fix the issue. This seems like the major fix for most people. The direct approach of sudo apt-get install libc.so.6 returns this: Reading package lists... Done Building dependency tree Reading state information... Done E: Unable to locate package libc.so.6 E: Couldn't find any package by regex 'libc.so.6' I guess libc.so.6 isn't a package, just a single file or something? I also tried gksudo gedit /etc/ld.so.conf.d/steam.conf Added these two lines, those the second one was all ready in the file, but copied over: /usr/lib32 /usr/lib/i386-linux-gnu/mesa Then executed: sudo ldconfig But nothing seemed to happen, steam still doesn't work. So, I feel like it is more likely that I have the library and steam isn't looking in the right place. One thing I've seen is people usually reference /usr/local/lib/ for your library locations. However, I can't find where to cd into /usr/, it isn't in my home folder. If /usr/ is the home folder, there is only a /.local folder which only has /share, no lib anywhere. Sorry for my linux ignorance. I appreciate any help, I honestly have no idea how to confirm I have the library and point steam to it, or if that is even the right thing to do. Edit: Tried this, not entirely sure what it means ~$ ls -l /lib32/libc* -rwxr-xr-x 1 root root 1721832 Sep 30 11:06 /lib32/libc-2.15.so -rw-r--r-- 1 root root 185928 Sep 30 11:06 /lib32/libcidn-2.15.so lrwxrwxrwx 1 root root 15 Sep 30 11:06 /lib32/libcidn.so.1 -> libcidn-2.15.so -rw-r--r-- 1 root root 34316 Sep 30 11:06 /lib32/libcrypt-2.15.so lrwxrwxrwx 1 root root 16 Sep 30 11:06 /lib32/libcrypt.so.1 -> libcrypt-2.15.so lrwxrwxrwx 1 root root 12 Sep 30 11:06 /lib32/libc.so.6 -> libc-2.15.so

    Read the article

  • Best Practice Method for Including Images in a DataGrid using MVVM

    - by Killercam
    All, I have a WPF DataGrid. This DataGrid shows files ready for compilation and should also show the progress of my compiler as it compiles the files. The format of the DataGrid is Image|File Path|State -----|---------|----- * |C:\AA\BB |Compiled & |F:PP\QQ |Failed > |G:HH\LL |Processing .... The problem is the image column (the *, &, and are for representation only). I have a ResourceDictionary that contains hundreds of vector images as Canvas objects: <ResourceDictionary xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation"> <Canvas x:Key="appbar_acorn" Width="48" Height="48" Clip="F1 M 0,0L 48,0L 48,48L 0,48L 0,0"> <Path Width="22.3248" Height="25.8518" Canvas.Left="13.6757" Canvas.Top="11.4012" Stretch="Fill" Fill="{DynamicResource BlackBrush}" Data="F1 M 16.6309,18.6563C 17.1309,8.15625 29.8809,14.1563 29.8809,14.1563C 30.8809,11.1563 34.1308,11.4063 34.1308,11.4063C 33.5,12 34.6309,13.1563 34.6309,13.1563C 32.1309,13.1562 31.1309,14.9062 31.1309,14.9062C 41.1309,23.9062 32.6309,27.9063 32.6309,27.9062C 24.6309,24.9063 21.1309,22.1562 16.6309,18.6563 Z M 16.6309,19.9063C 21.6309,24.1563 25.1309,26.1562 31.6309,28.6562C 31.6309,28.6562 26.3809,39.1562 18.3809,36.1563C 18.3809,36.1563 18,38 16.3809,36.9063C 15,36 16.3809,34.9063 16.3809,34.9063C 16.3809,34.9063 10.1309,30.9062 16.6309,19.9063 Z "/> </Canvas> </ResourceDictionary> Now, I want to be able to include these in my image column and change them at run-time. I was going to attempt to do this by setting up a property in my View Model that was of type Image and binding this to my View via: <DataGrid.Columns> <DataGridTemplateColumn Header="" Width="SizeToCells" IsReadOnly="True"> <DataGridTemplateColumn.CellTemplate> <DataTemplate> <Image Source="{Binding Canvas}"/> </DataTemplate> </DataGridTemplateColumn.CellTemplate> </DataGridTemplateColumn> </DataGrid.Columns> Where in the View Model I have the appropriate property. Now, I was told this is not 'pure' MVVM. I don't fully accept this, but I want to know if there is a better way of doing this. Say, binding to an enum and using a converter to get the image? Any advice would be appreciated.

    Read the article

  • Raid superblock missing on single parition. Recovery needed!

    - by user171639
    Ok so I have a 2 TB raid 1 setup that has three partitions: sdc1: linux sdc2: swap sdc3: LVM for data However the LVM will no longer mount. So I thought that I would take the first drive, mount it in linux (ive done this b4), and reset the spare drive to copy the data. Normally I can mount a single drive for data recovery using: sudo su apt-get install mdadm lvm2 mdadm --assemble --scan modprobe dm-mod vgscan vgchange -ay c mount -o ro /dev/c/c /mnt Unfortunately, vgscan doesnot recognize the data partition. It appears as though the superblock on the first drive's data partition was erased while syncing with the second. So now I cannot mount that partition and the second drive is stuck in spare mode. Any ideas? Or a way to force mount the data partition just to copy the data? knoppix@Microknoppix:~$ sudo su root@Microknoppix:/home/knoppix# apt-get install mdadm lvm2 Reading package lists... Done Building dependency tree Reading state information... Done lvm2 is already the newest version. mdadm is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 551 not upgraded. root@Microknoppix:/home/knoppix# mdadm --assemble --scan mdadm: /dev/md/1 has been started with 1 drive (out of 2). mdadm: /dev/md/0 has been started with 1 drive (out of 2). root@Microknoppix:/home/knoppix# modprobe dm-mod root@Microknoppix:/home/knoppix# vgscan Reading all physical volumes. This may take a while... No volume groups found root@Microknoppix:/home/knoppix# cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdc1[2] 4193268 blocks super 1.2 [2/1] [U_] md1 : active raid1 sdc2[2] 524276 blocks super 1.2 [2/1] [U_] unused devices: <none> root@Microknoppix:/home/knoppix# mdadm -v --assemble --auto=yes /dev/md2 /dev/sdc3 mdadm: looking for devices for /dev/md2 mdadm: no recogniseable superblock on /dev/sdc3 mdadm: /dev/sdc3 has no superblock - assembly aborted root@Microknoppix:/home/knoppix# dumpe2fs /dev/md0 | grep -i superblock dumpe2fs 1.42.4 (12-Jun-2012) Primary superblock at 0, Group descriptors at 1-1 Backup superblock at 32768, Group descriptors at 32769-32769 Backup superblock at 98304, Group descriptors at 98305-98305 Backup superblock at 163840, Group descriptors at 163841-163841 Backup superblock at 229376, Group descriptors at 229377-229377 Backup superblock at 294912, Group descriptors at 294913-294913 Backup superblock at 819200, Group descriptors at 819201-819201 Backup superblock at 884736, Group descriptors at 884737-884737 root@Microknoppix:/home/knoppix# Notes: I can read the super block from the spare drive. I was gonna try and restore the superblock from one of the backups, but i dont know how or if this would work. I also heard creating a new array (mdadm --create) using the same parameters will not delete the data on the drive but i didnt want to risk it. Recommendations?

    Read the article

  • New code release today - 2011.1.4.2

    - by Steve Tunstall
    Wow, two blog entries in the same day! When I wrote the large 'Quota' blog entry below, I did not realize there would be a micro-code update going out the same evening. So here it is. Code 2011.1.4.2 has just been released. You can get the readme file for it here: https://wikis.oracle.com/display/FishWorks/ak-2011.04.24.4.2+Release+Notes Download it, of course, through the MOS website. It looks like it fixes a pretty nasty bug. Get it if you think it applies to you. Unless you have a great reason NOT to upgrade, I would strongly advise you to upgrade to 2011.1.4.2. Why? Because the readme file says they STRONGLY RECOMMEND YOU ALL UPGRADE TO THIS CODE IMMEDIATELY using LOTS OF CAPITAL LETTERS. That's good enough for me. Be sure to run the health check like the readme tells you to. 

    Read the article

  • Will not supporting IE or older browsers drive away potential visitors/users of my site? [closed]

    - by XToro
    Normally a SO browser but this question doesn't fit there, hopefully it fits here. I just want to ask from web designers' point of view if it's wrong to not care about supporting Internet Explorer or older browsers. The site I'm designing looks great in all browsers except IE9-. There are certain things that IE doesn't support or behave like other browsers; webkit stuff, some CSS styles, drop-and-drop files from OS etc etc, but it all works great in Safari, FireFox, Chrome etc. Should I be that concerned? I know there are several people that use IE, but it's limitations have just been causing me more work by having to come up with workarounds. From what I've read, many of the issues I've been having should be solved with IE10, but not everybody keeps up to date. I know of several people who are still using IE6! Again, I'm hoping this is the right place to ask a question like this, and if not, please point me to the right stack exchange site instead of just downvoting me. Thanks! EDIT: Upon further research.... So far this year, IE(all versions) and Chrome have been neck and neck as the top, with IE only squeaking by Chrome, and FireFox a close 3rd. But looking at the top 10 browsers, IE6 doesn't even show up on this list in which the lowest percentage is 1.92%. Source : http://www.w3counter.com/globalstats.php?year=2012&month=7 Having a look at this other site, IE6 shows up in 11th place out of 12, just before "Other" http://www.sitepoint.com/browser-trends-february-2012/ This makes me a little more wary of not spending more time on IE compatibility. However, my site will not be going to a live beta until October or November, and I'm hoping that IE10 will have more features coded into it. Currently, I've written my upload page which is a "drag-and-drop files from the OS" type to simply display "IE is not supported", leaving no other option for IE users to upload pictures because I've spent so much time writing the uploader which does many things other than just upload the files. I will be changing this kinda cold "Access Denied" to a suggestion to upgrade, or install other browsers, with download links for each. Big thanks for the posts here and the interesting links!

    Read the article

  • Calendar icon in unity shows wrong date

    - by felix
    There is a column of icons in unity on the far left and one of them has the number "31" in big numerals. If you mouse over it it says "Google Calendar" and if you click on it you get google calendar which of course shows the correct date. Today is November 3. Shouldn't it say "3" instead? If I type "date" from the command line I get Sun Nov 3 21:19:37 GMT 2013 I see this was fixed for Chrome at least in 2011 http://gmailblog.blogspot.co.uk/2011/04/5-years-of-google-calendar-and-new.html .

    Read the article

  • [EF + Oracle] Inserting Data (Sequences) (2/2)

    - by JTorrecilla
    Prologue In the previous chapter we have see how to create DB records with EF, now we are going to Some Questions about Oracle.   ORACLE One characteristic from SQL Server that differs from Oracle is “Identity”. To all that has not worked with SQL Server, this property, that applies to Integer Columns, lets indicate that there is auto increment columns, by that way it will be filled automatically, without writing it on the insert statement. In EF with SQL Server, the properties whose match with Identity columns, will be filled after invoking SaveChanges method. In Oracle DB, there is no Identity Property, but there is something similar. Sequences Sequences are DB objects, that allow to create auto increment, but there are not related directly to a Table. The syntax is as follows: name, min value, max value and begin value. 1: CREATE SEQUENCE nombre_secuencia 2: INCREMENT BY numero_incremento 3: START WITH numero_por_el_que_empezara 4: MAXVALUE valor_maximo | NOMAXVALUE 5: MINVALUE valor_minimo | NOMINVALUE 6: CYCLE | NOCYCLE 7: ORDER | NOORDER 8:    How to get sequence value? To obtain the next val from the sequence: 1: SELECT nb_secuencia.Nextval 2: From Dual Due to there is no direct way to indicate that a column is related to a sequence, there is several ways to imitate the behavior: Use a Trigger (DB), Use Stored Procedures or Functions(…) or my particularly option. EF model, only, imports Table Objects, Stored Procedures or Functions, but not sequences. By that, I decide to create my own extension Method to invoke Next Val from a sequence: 1: public static class EFSequence 2: { 3: public static int GetNextValue(this ObjectContext contexto, string SequenceName) 4: { 5: string Connection = ConfigurationManager.ConnectionStrings["JTorrecillaEntities2"].ConnectionString; 6: Connection=Connection.Substring(Connection.IndexOf(@"connection string=")+19); 7: Connection = Connection.Remove(Connection.Length - 1, 1); 8: using (IDbConnection con = new Oracle.DataAccess.Client.OracleConnection(Connection)) 9: { 10: using (IDbCommand cmd = con.CreateCommand()) 11: { 12: con.Open(); 13: cmd.CommandText = String.Format("Select {0}.nextval from DUAL", SequenceName); 14: return Convert.ToInt32(cmd.ExecuteScalar()); 15: } 16: } 17:  18: } 19: } This Object Context’s extension method are going to invoke a query with the Sequence indicated by parameter. It takes the connection strings from the App settings, removing the meta data, that was created by VS when generated the EF model. And then, returns the next value from the Sequence. The next value of a Sequence is unique, by that, when some concurrent users are going to create records in the DB using the sequence will not get duplicates. This is my own implementation, I know that it could be several ways to do and better ways. If I find any other way, I promise to post it. To use the example is needed to add a reference to the Oracle (ODP.NET) dll.

    Read the article

  • [AJAX Numeric Updown Control] Microsoft JScript runtime error: The number of fractional digits is out of range

    - by Jenson
    If you have using Ajax control toolkits a lot (which I will skip the parts on where to download and how to configure it in Visual Studio 2010), you might have encountered some bugs or limitations of the controls, or rather, some weird behaviours. I would call them weird behaviours though. Recently, I've been working on a Ajax numeric updown control, which i remember clearly it was working fine without problems. In fact, I use 2 numeric updown control this time. So I went on to configure it to be as simple as possible and I will just use the default up and down buttons provided by it (so that I won't need to design my own). I have two textbox controls to display the value controlled by the updown control. One for month, and another for year. <asp:TextBox ID="txtMonth" runat="server" CssClass="txtNumeric" ReadOnly="True" Width="150px" /> <asp:TextBox ID="txtYear" runat="server" CssClass="txtNumeric" ReadOnly="True" Width="150px" /> So I will now drop 1 numeric updown control for each of the textboxes. <asp:NumericUpDownExtender ID="txtMonth_NumericUpDownExtender"     runat="server" TargetControlID="txtMonth" Maximum="12" Minimum="1" Width="152"> </asp:NumericUpDownExtender>                          <asp:NumericUpDownExtender ID="txtYear_NumericUpDownExtender"     runat="server" TargetControlID="txtYear" Width="152"> </asp:NumericUpDownExtender>                                                  You noticed that I configure the Maximum and Minimum value for the first numericupdown control, but I never did the same for the second one (for txtYear). That's because it won't work, well, at least for me. So I remove the Minimum="2000" and Maximum="2099" from there. Then I would configure the initial value to the the current year, and let the year to flow up and down freely. If you want, you want write the codes to restrict it. Here are the codes I used on PageLoad:     Protected Sub Page_Load(ByVal sender As Object, ByVal e As System.EventArgs) Handles Me.Load         If Not Page.IsPostBack Then             If Trim(txtMonth.Text) = "" Then                 Me.txtMonth.Text = System.DateTime.Today.Month             End If             If Trim(txtYear.Text) = "" Then                 Me.txtYear.Text = System.DateTime.Today.Year             End If         End If     End Sub   Enjoy!

    Read the article

  • Using extension methods to decrease the surface area of a C# interface

    - by brian_ritchie
    An interface defines a contract to be implemented by one or more classes.  One of the keys to a well-designed interface is defining a very specific range of functionality. The profile of the interface should be limited to a single purpose & should have the minimum methods required to implement this functionality.  Keeping the interface tight will keep those implementing the interface from getting lazy & not implementing it properly.  I've seen too many overly broad interfaces that aren't fully implemented by developers.  Instead, they just throw a NotImplementedException for the method they didn't implement. One way to help with this issue, is by using extension methods to move overloaded method definitions outside of the interface. Consider the following example: .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: Consolas, "Courier New", Courier, Monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } 1: public interface IFileTransfer 2: { 3: void SendFile(Stream stream, Uri destination); 4: } 5:   6: public static class IFileTransferExtension 7: { 8: public static void SendFile(this IFileTransfer transfer, 9: string Filename, Uri destination) 10: { 11: using (var fs = File.OpenRead(Filename)) 12: { 13: transfer.SendFile(fs, destination); 14: } 15: } 16: } 17:   18: public static class TestIFileTransfer 19: { 20: static void Main() 21: { 22: IFileTransfer transfer = new FTPFileTransfer("user", "pass"); 23: transfer.SendFile(filename, new Uri("ftp://ftp.test.com")); 24: } 25: } In this example, you may have a number of overloads that uses different mechanisms for specifying the source file. The great part is, you don't need to implement these methods on each of your derived classes.  This gives you a better interface and better code reuse.

    Read the article

  • Automatically change resolution when not in dock

    - by jwir3
    I have Ubuntu 11.04 (yep, I know it's old news) on my Lenovo W520. At home, I have a dock with dual monitors. I have a pretty decent setup - things work almost perfectly (hence the reason I'm reluctant to upgrade... that and I'm not 100% sold on Unity). Anyway, the only annoyance I have is that when I'm on travel, I use the laptop screen. When I un-dock the laptop, I need to manually go into nvidia x-server settings and change the resolution from 'Auto' to 1920x1200, or it will think I have two screens, and my mouse pointer will be able to go way off the left side of the screen. This isn't a big deal, but I need to do it every time I restart the x-server (so if I reboot, or have to kill it, etc...) What would be really nice is if there was a way for it to automatically detect whether or not there is external monitors (which it seems to do already), and switch into the mode I select, depending on which monitors are connected. Is there any way to accomplish this? I've posted my xorg.conf file for reference. # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 270.29 (buildd@allspice) Fri Feb 25 14:42:07 UTC 2011 # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 275.19 ([email protected]) Tue Jul 12 18:35:38 PDT 2011 #Section "Monitor" # Identifier "Monitor1" # VendorName "Lenovo" # ModelName "ThinkpadLCD" # #HorizSync 28.0 - 33.0 # #VertRefresh 43.0 - 72.0 # #Option "DPMS" #EndSection Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "DELL U2410" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 76.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro 1000M" Option "RegistryDwords" "EnableBrightnessControl=1" EndSection Section "Screen" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+120, DFP-6: nvidia-auto-select +1920+0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+120, DFP-5: nvidia-auto-select +1920+0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +1920+419, DFP-5: nvidia-auto-select +3840+0, DFP-6: nvidia-auto-select +0+0" # Removed Option "metamodes" "DFP-5: nvidia-auto-select +0+0, DFP-6: 1920x1200 +1920+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "NoLogo" "True" Option "TwinViewXineramaInfoOrder" "DFP-0" Option "TwinView" "1" Option "metamodes" "DFP-5: nvidia-auto-select +1920+0, DFP-6: 1920x1200 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection

    Read the article

  • Taking too long to get skills for entry level programmer position [closed]

    - by greenonion
    I don't have the skills for an entry level position as a .Net programmer. I am trying to learn what I need but there is too much to learn and too little time. What can I do? About two months ago, I went to a job interview for an entry level C# .Net programming/consultant position in NYC. When I heard back from them, they told me that the knowledge gap between what I knew and what they needed me to know was too big and I might have been a better fit if I had 6 months of experience. This was the first interview that I went on since graduating college. before the interview, I read a book on visual C#. Turns out it wasn't a very good book and I was missing a lot of key areas of knowledge such as ADO.net SQL (I had learned some LINQ) A little bit about how memory is handled Multiple threaded programming, etc. Because the book wasn't very good, the stuff I did know, I didn't know very well. I felt crushed. I've applied for jobs to gain experience but when recruiters hear that I have no experience they lose interest. I figured that I can at least work on my knowledge. Since then, I read "SQL Essentials" to cover the SQL bit and I found a pretty awesome book that is good enough to clear up what's hazy in my mind and covers almost all of the extra topics. The book is "C# 4.0: The Complete Reference" by Herbert Schildt. I'm even learning a lot about the topics I was familiar with. For a month now I've been working my way through this beast of a book. However, gaining the knowledge I need is taking too long. I can't hold off not having a full-time job much longer. I'm not stupid and I'm studying constantly pouring through the book, asking questions on stackoverflow, referencing the C# specification, etc. I have made great progress but there is just too much ground to cover. I'm on chapter 12 which is about a 3rd through the book. To get an idea of what I know vs don't know, the table of contents is on amazon: http://www.amazon.com/C-4-0-The-Complete-Reference/dp/007174116X How on earth can someone know enough to function as a programmer in the real world? Can I try for a job in academia? Will I have time to finish learning the rest of the C# language or am I just un-hireable?

    Read the article

  • A new free book from Microsoft - Programming Windows 8 Apps with HTML, CSS, and JavaScript (Second Preview)

    - by TATWORTH
    At  http://borntolearn.mslearn.net/btl/b/weblog/archive/2012/09/12/turn-your-bright-ideas-into-applications-with-the-new-mcsd.aspx there is mention of a new free book from Microsoft Press - Programming Windows 8 Apps with HTML, CSS, and JavaScript (Second Preview)The actual download page is http://blogs.msdn.com/b/microsoft_press/archive/2012/08/20/free-ebook-programming-windows-8-apps-with-html-css-and-javascript-second-preview.aspx

    Read the article

  • Oracle 11gR2:????(RAC/Exadata), ??, ????

    - by Yusuke.Yamamoto
    Oracle Database 11g ?????????????(RAC/Exadata)????????????? ???? 2010/11/17:????? 2011/01/07:???????:Exadata/?? 2011/01/18:???????:Exadata/????????????? 2011/04/21:???????:???????????? 2011/04/21:???????:Exadata/??????????????????????????????????? 2011/06/27:??????:Oracle Exadata Database Machine ????1,000??? 2011/07/06:???????:Exadata/????(?????????????????) 2011/07/08:??????:SAP?Oracle Exadata Database Machine??? 2011/07/15:???????:Exadata/????NTT????KDDI????????????? 2011/07/19:???????:Exadata/????(?????????????????) 2011/08/29:???????:Exadata/?????????(?????????) 2011/08/29:???????:Exadata/????? 2011/08/29:???????:Exadata/????(??????????????) 2011/10/27:???????:Exadata/??? 2011/11/08:???????:Exadata/NTT??? 2012/02/16:???????:Exadata/??????????????? 2012/03/21:???????:Exadata/?????????????(?????????????????) 2012/03/22:???????:Exadata/????? ?? Oracle Database 11g R2 ??????? Oracle Database 11g ?????????(????) Oracle Database 11g ?????????(????:Exadata?) ??????? Oracle Database 11g R2(???/????) Oracle Database 11g R2 ??????? ?? ??? 2009?11?11? Oracle Exadata Database Machine Version 2 ???? 2009?11?17? Oracle Database 11g R2 ???? 2010?02?01? ?????????????????????????????? 2010?03?31? SAP ? Oracle Database 11g R2 ??????????ISV????????·??????????? 2010?05?18? Windows Server 2008 R2 / Windows 7 ?????????Oracle Database 10g R2 ??? 2010?06?23? Oracle Application Express 4.0 ???? 2010?07?09? ?? Windows RDBMS ?????(2009?)????????? 2010?08?17? TPC-C Benchmark Price/Performance ???????? 2010?09?13? Patch Set 11.2.0.2 for Linux ???? 2010?10?20? Oracle Exadata Database Machine X2 ???? 2010?11?17? Oracle Database 11g R2 ????1?? 2010?11?19? ?? Windows RDBMS ?????(2010????)????????????? 2011?03?29? Oracle SQL Developer 3.0 ???? 2011?06?27? Oracle Exadata Database Machine ????1,000????????????????·?????????????? 2011?07?08? SAP ? Oracle Exadata Database Machine ??? 2011?09?01? Oracle Database Express Edition 11g Release 2 ???? 2011?09?23? Patch Set 11.2.0.3 for Linux ???? 2011?11?14? Oracle Database Appliance ???? Oracle Database 11g ?????????(????) ????????????????????????????????(????)? ?[RAC]:Oracle Real Application Clusters(RAC) ???????? ????(??????????) [RAC] ??????????(???) ????? [RAC] ????(???) ?????·???????·??? [RAC] ????? ????·??????·?? ???? ???????(??????????????) [RAC]|???99.999%???????500???????????? - ITpro ??????????? [RAC] ????(????) [RAC] ???(???) ????????(???) [RAC] ??????(???????????) [RAC] Oracle Database 11g ?????????(????:Exadata?) ????????????????????????????????(????)? ?Exadata ??????Oracle Database 11g / Oracle Real Application Clusters(RAC) ?? ?()??????????????? KDDI(??????????????) NTT??? NTT???(???????????) ??????????????? ??? ????(??????) ????????????? ?????·???????·??? ??(??????????????) ?????(??????????) ?????????(SCSK) ?????(????????????) ??????????(???????????) ????(???????) ??????? ?????? ????/????·???????? ???????????(???????/NTT??????????) ????? ?????????????(????/????????????) ???? ????????????|?????? ????|?????????????2013?2????3??????????? - ITpro ??? ?????? ??? ?????(SCSK)|DWH?????????????? - IT Leaders ????(???????????)|???????????·??????????????????????? - oracledatabase.jp Customer Voice ????:????IT?????24??365????????????????????? ?Oracle9i Database ?????????????????????Oracle Database 11g ???????????????????????? Oracle9i Database ???????????????? Customer Voice ??????:Oracle Database 11g????????????????????? ?Oracle ASM ???????????????????I/O????????????????????????????????????? ??????? Oracle Database 11g R2(???/????) ???????????????? Oracle 11g R2 ????????? - IT Leaders ??????????11g R2?5???? - ??SE????Oracle??? - Think IT ????????????????????????~Oracle Database 11g Release2 ????????? - oracletech.jp ??????????? Oracle Database 11g Release 2(11gR2)|??????????? Oracle Exadata|??????????? ???????|???????????

    Read the article

  • ??????????? ??????? ?? Oracle CRM On Demand ??? ????????? Oracle

    - by [email protected]
      ?????? ??? ?????????????? ????????? ORACLE! ?????????? ??????????? ??????? ?? ??????? ???????? ?? CRM On Demand ???? ???????? ? ????????? ?? 1-?? ?????????? ? ????? ?????????? 59$ + ???.   ??????????? ????????????? ??? ???????? ?? ???? ?? 12 ??????? ???? ???????? ???????????: ?? ????? ??? 2010 ???? ????????? - ???????????? ??????? ?????? ???????? ??????????? ????????-???????? Oracle ** ??????? ???? ?????????? 70$ + ??? ???????? ????? ?????????????? ?????: Oracle Partner Relationship Management On Demand, Oracle CRM On Demand ??? iPhone ?? ???? ?? $20+??? ? ????? ?? ????????????.

    Read the article

  • ???TCO?????????!? WebLogic Server vs. JBoss Enterprise Application Platform

    - by Tatsuhiro Yamaguchi
    WebLogic Server?????????????Java EE??????????·?????JBoss Enterprise Application Platform(EAP)????????????????WebLogic Server?????????JBoss EAP????????????????????????????????????????TCO(??????)???????????...?????????????????????????1?????????????????????????????????TCO?JBoss EAP??WebLogic Server??????????????????????(???) ????????????????????????WebLogic Server??Java????????????? Java EE??????????·???????????WebLogic Server????????????????????·?????????????????????JBoss EAP??JBoss EAP?????????????????????·??????????????????????????????????????????????????????????????????? ????????·?????????????????????????????????1?????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????? ?????????????????????????????????????????????????????????????????????????????????????????????????????????????????????? ????????????????Java??????????????????????????Java SE 6?????????????2013?2????????????????????????????????????????? ?????? Java SE 6????????????????(Oracle Technology Network) ???????????????JBoss EAP 5????Java SE 6??????????2013?2??????????????????????????????????????? ?????2012?8????????????JBoss EAP 6????????? ????Java SE 7?????????Java SE 7?????????????2014?7??????????JBoss EAP 6????????????2013??????????????????????????????Java SE 7???????????????1????????????????????????????Java SE 7????????????????????Java SE??????????????????????????????? ???????WebLogic Server??????????????????Java SE???????????????????Java SE 6?2016?12????Java SE 7?????2019?7???????????????????????????????????????????WebLogic Server????????????????????????????????Java SE??????????? JBoss EAP?????????????????Java SE????????????Java SE???????????????????????WebLogic Server??????????????????JBoss EAP?????????????????????????????????? ??????????????????WebLogic Server?????????????????? ??????????????????JBoss EAP?WebLogic Server????????????1????????????????WebLogic Server????????????????????????????????????????????????????????????????? ???JBoss EAP?????????????????????????????????????????????????????????????????????????????????????????WebLogic Server??????????????????????? ?????????????????????????????????????????????WebLogic Server?JBoss EAP?????????????????????????????????????????????????????????????????????????????????????????????????????WebLogic Server?JBoss EAP????????????? ??????????????? 3~6????????WebLogic Server????????????????????????WebLogic Server??? ??????????????????????????????????????????????????? JBoss EAP??2????????????24??365????????????Premium?????(??~??)9?~5????????????Standard??????????????????????????(CPU?????????????16??)???????????6???????????????????? · JBoss EAP Standard · JBoss EAP Premium » ???????:?0 » ???????:?0 » ??????:?85?/1?? » ??????:?125?/1?? » 6?????:?85?×6?=?510? » 6?????:?125?×6=?750? ???WebLogic Server???????????????????????????????/?????????CPU??????(CPU????????)?8???CPU?2?(CPU???=16??)??????????????????????6?????????????? · WebLogic Server Standard Edition » ???????:?216?(?108?×2CPU) » ????:?48?/1??(?24?×2CPU) ?????????22% » 6?????:?216+?48?×6=?504? ????JBoss EAP Standard??Premium?WebLogic Server Standard Edition???????????????????? ???????JBoss EAP Premium???3?????Standard??6????????????? ???????????WebLogic Server Standard Edition?????????????????????JBoss EAP????CPU??????????WebLogic Server Standard Edition?CPU?????????????1CPU????????????????????WebLogic Server Standard Edition????????????? ?????WebLogic Server??Java???????????????????????????????????????JBoss EAP?????????????Java SE????????????????????????WebLogic Server???????? ????WebLogic Server???????????????????????????????????JBoss EAP???????????????????????????????????????WebLogic Server?????????????????????WebLogic Server??????????????·??????????????????? ???2012?9????Oracle Technolorgy Network???????????WebLogic Server???????????????????????????????????????????????????????? ????????????????????????????????JBoss EAP????TCO???????????????????????????????????WebLogic Server????????????????????????????WebLogic Server????????????????????????????????????????????

    Read the article

  • ???? : ?????????????????????????? ~??????????????????SCSK??????

    - by Shinji Watanabe
    ??????????????????????????????????????????·?????????????????????????????????????Web??????????????????????????????????·??????????????? ?????????????·???????????????????????Web CMS?EC????????????????????????????????????????????????????????Web??????????????????·???????????????Web??????????????????????????????·??????????Web???????????????? ???????? ?? 2012?10?10?(?)14:00~17:15(??13:30~) ?? Web?????????????????-·??????????????????????Web????????????????????????????????·??????????Web????????????????????????????Web???????????????Web?????????????????????????????? ?? ???????????????????2-4-27 ????? 9F???:??? ???? ?????? 10????? ??5???????? ??3?(????????????????)JR? ????? ?????? ??10?JR??? ?????? ????? ??5??? ???? ?????? 7????? ??5?????? ?? ?? ?? 50????????????????????????????????????????????????????????????????(??????????????????????????????????)?????????????????????????????????????????????????????????????????????????????????????????????????????1?2???????????????????????????????????? ?? ??????????????????????????SCSK???? ???????? ????????? ????? 13:30-14:00 ?? 14:00-14:10 1)??????????????? Fusion Middleware?????? ????/??????? ? ? 14:10-15:00 2)?User Experience ??? ~ ????????????????????????????????? ????????CEO ?? ????????????????????????????????????????????·?????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????? 15:00-15:45 3)?B2C?B2B?????!?????????????????????3?????????????? ?????????????? CRM/HCM???????????? ?? ?? ?E?????????????????????????????????????????????????????????????B2B?B2C?????????????????????????????????????????????? ????????????????????????????????????????????????????? ???????????????????????????????????????????3??????????? 15:45-16:00 ?? 16:00-16:45 4)????????????????No.1 ??????????????????????SCSK???? ?????????? ??????????????????????? WEB???????? ??? ? ? ????????????????Web????PfizerPRO??????????????????????????????????????????????????????????????????????????????????????????????????????????????? ????No.1(?)? ???? ???????????SCSK??????Web???????????????????????????????????????????????????????????????????????????????????????????????????? ???:??????·??·???2011?12?14??? 2011?7~9????????????????? 16:45-17:15 5)????Web????????????????~???????????????????????????~?SCSK???? IT??????????? ???????????????? ?? ??????????????????????????????????????Web????????????????????????????????????????????CMS????????Web???????????????????????????????????????????? ??????????????????????????????

    Read the article

< Previous Page | 371 372 373 374 375 376 377 378 379 380 381 382  | Next Page >